SeaDek Coaming Bolsters are a great alternative to traditional upholstered bolsters. Durable and easy to install, these bolsters will provide years of trouble-free service thanks to their closed cell PE/EVA construction and robust 3MTM pressure sensitive adhesive. Each set contains two 4.5” x 37” bolsters that are 20mm thick.
Rated 5 out of 5 by PeterM from Better than expected replacement for my 25' boat I am a Florida boater and here the Sun UV rays destroy expensive upholstery in a few year. Unfortunately most boat manufacturers re-design upholstery every few year and it is impossible to replace damaged parts on used boats. I ordered three pairs of SeaDek coaming bolsters and very satisfied with the result. First, it took me less than an hour to install all six pads. The pads do not require any drilling. They attach to the side of your boat by an incredibly strong glue already pre-installed on the pad. You just simply remove the protective foil and the pads just stick to your boat. The pads are on my boat for over a month and look very nice and professional.
Date published: 2017-12-28
Rated 3 out of 5 by Docc from Not "right" enough for the price While the material and workmanship of all these products are really good and the instructions clear and concise, these coaming bolsters are just too hard to be worth the $400-$500 it takes to outfit my 25' CC. This isn't a "foam" or a "cushion" in any sense; it is a stiff/hard and dense material. That said, yes, it IS softer than fiberglass, but not by much. Especially here in Florida where we don't normally fish in long pants, bare knees need more cushioning.
Date published: 2016-06-19
Rated 4 out of 5 by sandiegosteve from Looks great, easy to install After years of beating up my knees, I've been looking at coaming bolsters for a while. For the price, these are very well built, look great and are easy to install. They do provide some cushion, but they are not the same as the custom foam ones (very expensive). So, to add comfort and looks at a great price, these are a great option.
Date published: 2015-07-22
Rated 5 out of 5 by RRealtyPro from Coaming Bolster Used this product to replace some foam seating I had on top of a rocket launcher and center console seating as well. Installed it about three years ago. The white top was getting dirty all the time but cleaned up easily. Found out that if I put some silicone spray with UV filter in it it would stay cleaner longer. Good product, will be easy to remove and replace when needed. I estimate I will get at least another 2 to 3 years out of it. Better look, longevity and comfort than the foam product that was there before.
Date published: 2015-10-10
Rated 5 out of 5 by Nails from Coaming pads I had previously recovered my coaming pads on my 28 Marlin Grady white three times, . I have my own shop that does this all the time and I prefered the look and durability of your pads . I show them off to everyone at the marina and get complements all the time . I love them and recomend them to everyone who has coaming pads on there boat . Great product .
Date published: 2015-10-09
Rated 5 out of 5 by Joliet Jake from My Knees Love These! I have had these in Bimini Blue color on my 19' Dusky for four years now and they still look great. Have been covered with bluefish blood, squid bits dried in the sun, and many other unsavory ingredients from long days of fishing and wash up great. Very comfortable when bottom fishing / jigging and more durable than vinyl covered foam pads.
Date published: 2015-12-07
Rated 5 out of 5 by opbam from Knee savers I bought coaming bolsters for the rear and sides of my new boat. Not only do they look beautiful and ad a sharp look to the boat but they save my knees every time I take my boat out fishing. They are a little pricey but you cannot put a value on looks and comfort plus reliability.
Date published: 2015-10-12
Rated 1 out of 5 by Not happy from Custom floor for my KMV 1700ht Not happy with sea deck product Always dirty looking ,have to wash floor after every time out Flooring is about an inch short....template should be within 1/16 of finished floor ,complained about it at Miami boat show and sea deck never acknowledged
Date published: 2017-04-22
I have a 306 grady white bimini. How much is it for your bolsters? How do you get the rounded deck on the stern around the live well and corners? 10 ft beam and o 20 ft on each side from stern to bow.
Hello Lou, Thank you for your inquiry. Please reach out to firstname.lastname@example.org with the dimensions you need made for the bolsters and we would be happy to provide you with a quote. Also if you send a photo of the rounded deck and live well you are referring to they will be able to look at that and let you know if the bolsters would be able to work there, Thank you, Customer Advocate Team SeaDek Marine Products 5440 Schenck Ave. Rockledge, FL 32955 321-632-4466 Phone 321-806-4387 Direct www.seadek.com
Date published: 2018-12-12
Will these work on a bend of approx 30 degeees toward the end?
Hello Westcostwillie, Thank you for your interest in SeaDek. We do not recommending bending the bolsters. This pulls on the pad away from the surface and may cause the pad to lift off and not stay adhered as long as desired. We would recommend make the bolsters two parts. If you have any further questions please reach out out to email@example.com Thanks, Customer Advocate Team SeaDek Marine Products 5440 Schenck Ave. Rockledge, FL 32955 321-632-4466 Phone 321-806-4387 Direct www.seadek.com
Date published: 2018-12-12
do these come in a smaller size like 3.5 inch width?
Hello JFDavies26, Thank you for your interest in SeaDek Marine Products. We do not offer a smaller bolster on the website, but would be happy to review pricing for custom bolsters with you. Please contact firstname.lastname@example.org and a representative will get back to you with pricing for your custom bolsters. Thank you, The SeaDek Customer Service Team SeaDek Marine Products 5440 Schenck Ave Rockledge, FL 32955 321-632-4466 Phone 321-632-7019 Fax www.seadek.com
Date published: 2018-09-27
I recieved your little sample pack, thank you but could I get a list of what each is by chance? Especially the black and grey three piece horizontal strip?
Hello, Thank you for leaving a question for us. Each of your sample pieces should have a name on the back of them. The grey over black piece is our storm gray over black teak option. You can, however, have teak done with other color combinations as well. Please feel free to contact us if we can be of further assistance to you.
Date published: 2018-07-30
can I purchase coaming pads in custom sizes? 6" x 12" with about 1/2" thickness?
Thank you for your interest in SeaDek. We would be happy to email you directly with a quote for custom bolsters. Thanks The SeaDek Customer Service Team SeaDek Marine Products 5440 Schenck Ave Rockledge, FL 32955 321-632-4466 Phone 321-632-7019 Fax www.seadek.com
Date published: 2018-06-28
need 56" long bolsters price ? Will this stick to powder coated allum ?
Thank you for reaching out to us about your need for custom bolsters. We will be happy to email you directly with pricing and ordering options. In regards to the adhesion of SeaDek to powder coat, With the large number of decks on the market there is no real way for us to be certain SeaDek will properly stick to all surfaces. SeaDek generally adheres to most smooth surfaces very well so long as it is properly prepped prior to installation. The best way to know for sure that SeaDek will stick to your surface is to test it with a small sample piece. Sample kits can be requested on our website.
Date published: 2018-06-28
can this be custom ordered to be 3 1/2 wide?
Yes, you can custom order different size. Please submit coaming bolster request using the link below. https://www.seadek.com/quoteformcoamingbolsters.aspx
Date published: 2018-05-15
Can the coamings be fitted in a corner? In other words, can you 'make a turn' with the coaming or should I plan to use two coaming and have them meet in the corner?
Thank you for reaching out to us in regards to our Coaming Bolsters. The pads are 20MMs thick and will not bend into a corner. The pads will need to stop before the corners.
Date published: 2018-04-17